Skip to content
Same-day shipping before 13:00 CET!
On January 13th 2023 our store is closed. Sorry for the inconvenience.

Sika Repair 20F for concrete repair and leveling 25kg

by Sika
Original price 111,50 zł - Original price 111,50 zł
Original price
111,50 zł
90,65 zł netto
111,50 zł - 111,50 zł
Current price 111,50 zł
90,65 zł netto

Stock Available: 17

ikona dostawy Koszt dostawy: od 11,99 zł - [Więcej]


Sika Repair Mortar 20F is concrete repair and leveling product . It is a one-component PCC-type mortar, which was created on the basis of polymer-modified cement . It contains it microsilica addition and is reinforced with synthetic fibers. The mortar is used primarily for manual reprofiling and leveling of rough concrete surfaces. As a result, a layer from 4mm to 20mm when applied to the entire surface and up to 40mm when filling local defects.


  • Non-toxic material
  • Increased resistance to penetration by water and chlorides
  • Product with high resistance to sulphate corrosion
  • Good strength, water and frost resistance properties
  • Compensation for early shrinkage thanks to the addition of synthetic fibers
  • Good adhesion without the use of a bonding layer
  • Ease of obtaining a perfectly cosmetic surface
  • Ease of preparation
  • Easy to apply

What is the use of 20F putty?

Putty for repairing and leveling concrete Sika Sepair 20 F is intended for structural and non-structural repairs by hand. It is ideal for concrete exposed to increased environmental aggression. It is applicable in general construction and hydraulic engineering .

How to properly apply the mortar?

Sika Repair 20F can be applied using traditional techniques. Mortar can of course be applied by hand or by wet spraying . Remember that the substrate must be matt-damp before applying the mortar. While the bonding layer is applied Sika Repair 10F onto the previously prepared substrate with a stiff brush apply it to the surface with a rubbing motion . Apply Sika Repair 20F to the fresh bonding layer with a trowel or trowel. The layer must be pressed to the substrate and then removed with a shearing motion. If the use of Sika Repair 10F is not necessary, Mortar 20F is applied in this way to the matt damp substrate.


  • Chemical base: Cement, polymer, microsilica, synthetic fibers, selected aggregate, special additives
  • Packing: 25 kg bags
  • Appearance / Color: Gray powder


Mixing ratio

Sika® Repair-20 F : water - 100 : 14 by weight 3.5 liters of water per 25 kg bag. To increase the stickiness and stability of the mortar (e.g. in a vertical, overhanging or ceiling position), the amount of water can be reduced to approx. 3.25 liters per 1 25 kg bag.


Theoretical consumption: ~18.5 kg/m²/cm. Practical consumption depends on the roughness of the substrate, method of application, losses during application.

Layer thickness

Minimum 0.5 cm / Maximum 1.5 cm - leveling mortar. When repairing minor local defects - maximum 3.0 cm.

Waiting Time / Overcoating

The minimum technological break before applying any subsequent layers is (at +20°C):

  • for Sika® Repair-30 F: minimum 12 hours
  • for one-component Sikagard® coatings: minimum 5 days
  • for two-component coatings such as Icosit® and Sikafloor®: not less than 7 days and not earlier, until the moisture content of the material drops below 4%

Szczegółowe informacje w Karcie Informacyjnej Produktu*
*(Otwarcie w nowym oknie z oficjalnej strony producenta)

Additional information

Have additional questions?

Contact us!

Buy cheaper

For selected products, the discount is calculated automatically based on the quantity in the cart!


Time to withdraw from the contract: 14 days

(detailed rules for returning products can be found in the tab: return of goods)


Time for a warranty claim: 2 years

(warranty excluded for entrepreneurs to the extent permitted by law)